This page describes how to install an image to the nand flash of Marsboard RK3066, ie, how to flash the board. You can choose to either flash the whole image (ie, update.img) to the board or just flash the selected partitions. You can download the prebuilt images or from our server the images.

Follow these steps - How to Install Rockchip USB Driver on Windows 7 / 8 / 8.1 / 10 PC, if you want to install Rockchip device drivers with.exe file install.
Installing driver goes like this: 1. Windows / Open Control Panel (you wanna have this open before starting the above procedure) 2. Select 'System' 3. Open 'Device Manager' 4. Watch the list as it will change upon detection of a new device. It should add something like 'Class of Rockchip Devices' near the top of the list.

2Windows
- 2.1Install driver
- 2.2Flash Image
3Linux
- 3.1Using Linux Upgrade Tool to flash update.img

Before you start

Linux kernel for radxa rock/rock pro/rock lite/rock2 series. radxa/linux-rockchip.

Keep in mind that:

What you will need to flash the board is:

a MarsBoard RK3066 board
a PC running Windows (XP 32/64bit, Windows 7 32/64 bit) or Linux (32/64bit)
a micro USB cable with one side plugged in to the OTG port of MarsBoard and the other side plugged into the USB port on PC.

Rockchip Rk30sdk Drivers For Maclastevil

Windows

The Windows tool for flashing the image is provided by Rockchip. To flash the update.img, you need to use the RKBatchTool and to flash the partitions, you will need to use RKDevelopTool. Both RKBatchTool and RKDevelopTool rely on the RK USB driver so you will need to install it first as below:

Install driver

There two ways to install the driver under Windows:

install using RKDriverAssistant tools - the easy way
install manually

If you have already installed the USB driver please skip this step.

Install using RK Driver Assistant tools

There’s no need to connect your Rockchip device during this procedure just download and extract RKDriverAssistant.zipThen double click on DriverInstall.exe in the RKDriverAssistant directory to start the utility.If you've previously tried to install the Rockchip USB drivers for any Rockchip devices make sure you click “Uninstall Driver” first.

Then click “Install Driver”, and depending on your version of Windows the Security below may show up twice during installation. Just click “Install”

when the driver has finish installing then shut down MarsBoard and connect the MarsBoard to your computer and let the board go to recovery mode, then your computer will detect the board and you will see it within device manager.

Now the driver should have been installed successfully!

Install Manually

Download the file (Rockusb_Driver_v3.7.rar) from here and shut down the MarsBoard then connect the MarsBoard to the computer and let the board go to recovery mode. After your computer should detect the board and you will see an unknown device within device manager.

Select the Unknown device then right click and select 'Update Driver Software'.

Select 'Browse the computer for driver software'.

Find the file unzipped file you downloaded earlier (Rockusb_Driver_v3.7.rar) and select either the 32/64bit folder then click 'OK' to install.

When the driver is installed successful you will then see a Rockusb Device in the device manager window.

Now the driver is installed successfully.

Flash Image

There are two methods to flash an image use android tools.

use Download Image (can flash by partitions)

use upgrading firmware (flash update.img only, it will erase everything.)

Using AndroidTool to flash update.img (Firmware)

Download AndroidTool from here. Then unzip it and double click AndroidTool.exe

Select an image (RK3066 update.img), click Firmware. For information on how to make an update.img see update.img

Power down the MarsBoard and connect the MarsBoard to the computer then let the board go to recovery mode after the program should detect the device.

Click the 'Upgrade' button to begin flashing and when the flashing process finishes successfully you will see the following interface.

If the flashing has aborted ,it could possibly be an error with the update.img, you can either try to redo the operations above or make the update.img again!

Using AndroidTool to falsh image by partition

Download AndroidTool from here. Unzip it the file and double click AndroidTool.exe.

Power down the MarsBoard and connect the MarsBoard to the computer and let the board go to recovery mode then the program will detect it.

There are eight selections to choose from so select the correct row and then select the checkbox to the left of the row to select it. After you must click the column on the right side for the path of the file you want to flash. You can then select one or more files and flash them at once. Finally Click 'Run' to flash images to the device (the right most selection shows the log of the progress).

If successful the board will disconnect from the tool and boot into the system.

Please Note:

The kernel is contained within the boot.img when you package the image by './mkimage.sh ota' please see Android Build for more information.
you can flash one of more image at one time as needed

Preparing IDB failed

This happens at upgrading bootloader, if you need to upgrade the bootloader or the update.img contains a new bootloader, you probably will meet this. The marsboard is 'bricked'. Follow this unbrick instructions to unbrick it.

Linux

Rockchip has provided tools for upgrading within Linux (closed source) since Android 4.4. The initial RE work of the Rockchip bootloader updating protocol is by naobsd and has been improved by some in rkflashtool. linuxerwang has made a GUI version of the rkflashtool called rkflashkit.

Warning: both rkflashtool and rkflashkit can not flash the update.img.

Using Linux Upgrade Tool to flash update.img

Download the Rockchip linux upgrade tool here. Unzip it and you will get a file called upgrade_tool which is a binary executable file under Linux.

Flash update.img

Let the board go to recovery mode and run the following command to flash the update.img:

Lowlevel Format nand

If you have an error with upgrading you can low level format the nand flash first with the following command:

Flash parameter

Flash bootloader

Flash the boot.img

Flash the kernel.img

Others

There are other commands in the upgrade_tool, such as:

Installing RkFlashKit

Rockchip Rk30sdk Drivers For Maclastevil Epson

In order to install RkFlashKit in Debian or Ubuntu, you need to get the source code, build it,You can download the pre-built rkflashkit here or build it yourself with the following command:

And install it with the following command

Flashing firmware with RkFlashKit

Run it with the following command

The tool is similar to RkAndroidTool as it can burn partition images to specific partitions. You’ll need to enter recovery mode just like you would do in Windows, by pressing the recovery button, before powering the device via the USB port, and connect the USB cable to your PC. RkFlashKit should automatically find your device, so you just have to select the correct NAND partition, select the image file to flash, and click on Flash image.